01看掉粉情況

　　01 Check the situation of losing followers

　　劣質膩子：用手指輕輕擦過涂有劣質的膩子的樣板表面，手指上會沾許多膩子粉。優質膩子：用手指輕輕擦涂有優質膩子的樣析表面，手指上十分干凈，膩子完全沒有發生掉粉的情況。

　　Poor quality putty: Gently rub the surface of the sample coated with poor quality putty with your fingers, and you will get a lot of putty powder on your fingers. High quality putty: Gently wipe the surface of the sample coated with high-quality putty with your fingers, and the fingers are very clean. The putty has not lost any powder at all.

　　02看被水溶后的膩子

　　02 Look at the putty that has been dissolved in water

　　劣質膩子：用手輕輕摩擦經過水沖后的樣板表面，手指會沾上許多被水溶掉的膩子。優質膩子：即使用手反復摩擦水沖后的樣板，手上都干干凈凈的。

　　Poor quality putty: Gently rub the surface of the sample after water flushing with your hand, and your fingers will get a lot of putty that has been dissolved by water. High quality putty: Even after repeatedly rubbing and rinsing with water by hand, the sample remains clean on the hands.

　　03看水沖后表面變化

　　03 Surface changes observed after water flushing

　　劣質膩子：劣質膩子樣板在經過水沖之后，會很快出現起泡、掉皮現象。優質膩子：以同樣的水流強度沖洗優質膩子樣板，膩子表面不會有任何異常。

　　Poor quality putty: After being washed with water, the sample of poor quality putty will quickly produce bubbles and peeling. High quality putty: Rinse the high-quality putty sample with the same water flow intensity, and there will be no abnormalities on the surface of the putty.

　　04看拉拔后的水泥表層

　　04 Look at the surface of the pulled cement

　　劣質膩子：拉拔之后，觀察膩子斷裂面。劣質膩子的斷裂面出現在其中一個水泥決的表層就是水泥表面的膩子已經被拔掉了。優質膩子：優質膩子的斷裂面出現在膩子本身的中間層，兩塊水泥表層仍然粘有膩子。

　　Poor quality putty: After pulling, observe the broken surface of the putty. The fracture surface of inferior putty appeared on one of the cement surfaces, indicating that the putty on the cement surface had been removed. High quality putty: The fracture surface of high-quality putty appears in the middle layer of the putty itself, and the two cement surfaces are still stuck with putty.

　　膩子粉主要看哪幾個方面？

　　What are the main aspects of putty powder?

　?、俪煞帧Ｄ佔拥闹饕煞质请p飛粉、灰鈣粉、水泥、膠粉、滑石粉、保水劑等組成，好的膩子粉使用的膠粉是天然植物膠，用來批墻無任何氣味。而傳統膩子粉需要加入膠水增加它的粘黏度，用來批墻會有一股讓人不適應的氣味。①環保性。膩子在家裝成本中的比例微乎其微，但其施工面積卻占到家裝總面積的80℅以上，若其環保質量不過關，所含有毒物質將在室內長期釋放，毒害居住者健康。環保標準：GB 18582-2020

　?、?Ingredients. The main components of putty are fly ash powder, calcium ash powder, cement, rubber powder, talcum powder, water retaining agent, etc. Good putty powder uses natural plant rubber powder, which has no odor when used to batch walls. Traditional putty powder requires the addition of glue to increase its viscosity, and when used to batch walls, it will have an uncomfortable odor Environmental friendliness. The proportion of putty in home decoration costs is negligible, but its construction area accounts for more than 80% of the total home decoration area. If its environmental quality is not up to standard, the toxic substances it contains will be released indoors for a long time, poisoning the health of residents. Environmental Protection Standard: GB 18582-2020

　?、谡辰Y(jié)強度。目前仍有一些用戶采用原始的方法調制膩子，用這種方法調制出來的膩子由于比例不當、計量不準、粘結力很差，所以極易出現起皮、脫落等弊病。另外市場常見的劣質膩子粉也往往沒有質量保證。③光滑細膩。膩子打磨后都會形成一些細小砂痕，這有利于乳膠漆的附著，但如果砂痕太粗，乳膠底漆難于填充覆蓋，就會影響涂層表面的光滑程度。④耐水性好。耐水性常常是決定膩子質量的一個重要指標，耐水性好的膩子不僅在發霉、受潮的條件下同樣保持良好的附著力，而且對涂料在其表面的成膜也具有很大的作用。⑤施工性。好的膩子施工好批刮易打磨，批厚不易自裂。⑥使用壽命。普通膩子粉遇水即變質，使用時間長了脫粉風化、起泡、開裂、脫落等現象都可能出現，使用壽命一般在三五年左右。而耐水膩子可以在水中浸泡檢測48小時，它的防霉、防堿、防潮能力更強，使用壽命長達10年以上。

　?、?Adhesive strength. At present, some users still use the original method to prepare putty. The putty prepared by this method is prone to problems such as peeling and detachment due to improper proportion, inaccurate measurement, and poor adhesion. In addition, low-quality putty powder commonly found in the market often lacks quality assurance Smooth and delicate. After polishing putty, some small sand marks will be formed, which is beneficial for the adhesion of latex paint. However, if the sand marks are too coarse, it will be difficult for latex primer to fill and cover, which will affect the smoothness of the coating surface Good water resistance. Water resistance is often an important indicator that determines the quality of putty. Putty with good water resistance not only maintains good adhesion under moldy and damp conditions, but also plays a significant role in the film formation of coatings on its surface Construction feasibility. Good putty construction is easy to scrape and polish, and the thickness of the putty is not prone to self cracking service life. Ordinary putty powder deteriorates when it comes into contact with water, and over time, phenomena such as powdering, weathering, foaming, cracking, and peeling may occur. The service life is generally around three to five years. And water-resistant putty can be soaked and tested in water for 48 hours, with stronger anti mold, anti alkali, and moisture-proof abilities, and a service life of more than 10 years.

本文由濟南巨野河福華建材廠友情奉獻.更多有關的知識請點擊:http://m.daquanq.com.cn/hyzx/856.html真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from Jinan Juye River Fuhua Building Materials Factory. For more related knowledge, please click: http://m.daquanq.com.cn/hyzx/856.html Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned