當我們把乳膠漆調制完成以后，其實就可以準備刷乳膠漆了。但是大家要注意，調制完的乳膠漆一般不能夠直接涂刷。乳膠漆的調配，一般是使用攪拌工具攪拌均勻，讓乳膠漆靜置15~20分鐘。這里主要的是讓里面的氣泡消泡，泡沫完全消除以后，就可以進行乳膠漆的正式的涂刷了。

After we have prepared the latex paint, we can actually prepare to apply it. However, it should be noted that the prepared latex paint cannot be directly applied. The preparation of latex paint is usually done by using a stirring tool to stir evenly and let the latex paint stand for 15-20 minutes. The main task here is to defoaming the bubbles inside. After the foam is completely eliminated, the latex paint can be formally applied.

①乳膠漆涂刷。此時我們就可以把工具用水潤濕一下，然后把工具內的水甩干，讓毛刷或者滾刷屬于濕潤的狀態。這樣用起來，會更加的快捷。然后就可以蘸取乳膠漆，此時就可以正式刷漆。

① Emulsion paint application. At this point, we can wet the tool with water and then shake the water inside the tool dry, leaving the brush or roller brush in a moist state. This way, it will be faster to use. Then you can dip in the latex paint, and then you can officially apply the paint.

②乳膠漆底漆的涂刷。對于乳膠漆的涂刷標準來說，一般都是一底兩面來完成涂刷的。首先我們要刷的是底漆。底漆一般都是使用滾刷來進行的，利用滾刷蘸取乳膠漆底漆，在墻面上進行滾涂就可以了。像乳膠漆底漆的施工順序一般都是先客廳后臥室，先頂把后墻面等一個順序來涂刷底漆。

② Application of emulsion paint primer. For the application standard of latex paint, it is generally done with one bottom and two sides. The first thing we need to apply is primer. Primer is usually applied using a roller brush. Dip the roller brush in the latex paint primer and apply it on the wall surface. The construction sequence of latex paint primer is generally from the living room to the bedroom, from the top handle to the wall, and so on.

③乳膠漆面漆的涂刷。乳膠漆面漆的涂刷，一般要刷兩遍，每遍之間要間隔2~4小時。所以在刷完底漆以后，一般停至兩個小時左右，看底漆基本干燥以后，就可以刷遍面漆。對于遍面漆，也是建議大家先刷頂板后刷墻面。在刷的時候，要一刷壓著一刷，如果使用滾刷，就是一滾刷壓著一滾刷，中間不要留有接茬。這樣把遍面漆刷完。讓其自然干燥。然后接著刷第二遍面漆。面漆的涂刷與遍面漆的涂刷方式是完全一樣的。

③ Application of latex paint topcoat. The application of latex paint topcoat generally requires two coats, with an interval of 2-4 hours between each coat. So after brushing the primer, it is usually stopped for about two hours to see if the primer is basically dry, and then the first coat of topcoat can be applied. For the first coat of topcoat, it is also recommended to brush the top plate first and then the wall. When brushing, one brush should be pressed against the other. If using a roller brush, it means that one roller brush is pressed against the other, without leaving any gaps in the middle. Finish the first coat of paint in this way. Let it dry naturally. Then proceed with the second coat of topcoat. The application method of the topcoat is completely the same as that of the first topcoat.

④養護。乳膠漆刷完以后，大家一定要注意養護時間。因為后期很多的乳膠漆出現了起皮，開裂，表面有顆粒，都是養護不到造成的。所以我們家里的乳膠漆的第二遍的面漆刷完以后，及時地關窗關門。這時個人建議大家家里裝修就暫時停滯，一般要停滯3~5天。這個具體的時間根據天氣狀況而定。例如夏天一般停三天就可以了，而冬季一般停滯五天左右，這樣才能保證乳膠漆表面好的效果。

④ Curing. After brushing the latex paint, everyone must pay attention to the curing time. Because many latex paints in the later stage have peeling, cracking, and particles on the surface, all of which are caused by inadequate maintenance. So after the second coat of latex paint in our home is applied, close the windows and doors in a timely manner. At this point, I personally suggest that everyone temporarily suspend their home decoration, usually for 3-5 days. The specific time depends on the weather conditions. For example, in summer, it is usually enough to stop for three days, while in winter, it is usually enough to stop for about five days to ensure a good surface effect of latex paint.

對于乳膠漆的施工，個人給出的觀點就是從膩子層的表面處理開始，到后乳膠漆的養護的完成，在這個過程中，就是整個乳膠漆的施工步驟。對于乳膠漆施工，大家需要注意的就是乳膠漆的調配，一定要關注。更多相關使用就來我們網站http://m.daquanq.com.cn咨詢吧！

For the construction of latex paint, my personal viewpoint is that from the surface treatment of the putty layer to the completion of the maintenance of the later latex paint, this process is the entire construction step of the latex paint. For latex paint construction, everyone needs to pay attention to the formulation of latex paint, and it is important to focus on it. For more related usage, come to our website http://m.daquanq.com.cn Consult!